Specifications : Scale: 1/8
Length: 95"/2415mm
Wingspan: 65"/1651mm
Turbine:10-16kg Features : F-15 is so popular a plane. Its aerodynamic outline, enables not only the original wonderful performance, so is the duplicated model. In jet world,this plane is even considered as a trainer by some modelers. Although JetLegend has already got a 1/10 scale one, F-15's features are not fully expressed due to its small size. When it comes to the decision on size options, a 1/7 scale one is too big which would use a turbine of at least P-180, while P-160 is more popular. With considering this, a 1/8 scale one came out under this situation. F-15 original size is: Wingspan 13.5m, length 19.43m. The model size is: wingspan 65in/1650mm, length 95in/2415mm. With this size, the producer has more space to exert. It's firstly shown in the design of the landing gear, as space is larger. A scale landing gear which is faithful to the original became possible, especially the rotation function of the wheels after retracting. Landing gear design : Main wheel size for this 1/8 scale F-15 is 4.25in, nose wheel is 3.25in. Wheel hubs and brakes are made by CNC, that guaranteed the likelihood to the original. Landing gear are installed in the fuselage with 4 pieces Ø3X10 hex screws. Note,they are hex screws, instead of wood self-tapping screws. It means saying goodbye to drilling holes in the wood. Just tap the hex screw, it's finished. It's so convenient for users. And it won't happen again that the gear mount wood is broken when landing. Assembling the metal components is a easier job.  
Wing design : Main wing dowel is made of carbon tube ( see Pic #3 ), which is perfect in intensity while light in weight. Work with the "U" mount plate ( see Pic #4 ) in fuselage, it's very easy for users to assemble/disassemble. Four mount plates like this are applied in this model.  
Same as the original, the main wing has aileron and flap. They are controlled respectively by two servos. Servo size is standard size ( 40mmX36mmX20mm ), such as Hitec HS-945 MG, easy to fit in.( standard size servo with 10KG or above torque is recommended). Note, parts in Pic #4 are in standard package too.  
 
Rudder Design : There are two aluminum rods for the rudder. They are also linked to the fuselage with mount plate ( see Pic #8 ). It's also easy to assemble/disassemble like the wing. For rudder servo, small size servo with 6 KG torque ( size 30mmX34mmX10mm ) is recommended, such as Hitec HS-5125 MG.
  Horizontal stabilizer design : In jet world, the design of horizontal stabilizer is always a key factor, especially the control mechanism. Not only flexible movement, but also adequate intensity is required. JetLegend's "One-Piece" design is fully satisfying this requirement. Horizontal stabilizer mount plate ( Pic #13 ) has two ball bearing to support. Two lock nuts lock the horizontal stabilizer tightly. At the meantime, a secure dowel is applied in order to avoid it from being loose. Servo installation and the whole control mechanism are "One-Piece". As long as the control mechanism is installed,the whole horizontal stabilizer is installed. This design is greatly helpful to users. Elevator servo needs a big torque. So standard size servo (40mmX36mmX20mm ) with 12KG or above torque is recommended.  
 
 
Intakes : The intakes are moveable. They are driven by servos. The function is realized with one channel setup. Activeness of intake/elevator combined control and elevator single control are interchanged by a switch on the transmitter.Intakes are free to move like the original during flying and can be shut down with the switch when it's not used.  
Air brake design : Back hatch cover air brake, This is a usual design, but the cylinder control is mostly like the original. The close end is connected to the open end with a steel tube instead of air tube. This looks more like the original and easier to use.  
| 
Airplains 
